粗大浓稠硕大噗嗤噗嗤h,精品人妻码一区二区三区,国产av无码专区亚洲精品,日韩a片无码毛片免费看小说

河北駿豪機械設備有限責任公司

聯系人：張經理13933000298

堆高車起重?zé)o力或不能起重原因：齒輪泵與泵提磨損過度；換向閥內的溢流閥高壓不當；油壓管路漏油；液壓油油溫過度；門架滑架存在卡阻現象；油泵電機轉速過低。解決方法：更換磨損或齒輪泵；重新調整；檢查并修復；更換不合格的液壓油并檢查油溫度升高的原因；檢查并調整；檢查電機并排除故障。
Stacker crane lifting to reason: the gear pump and the pump provided excessive wear; high pressure solenoid valve relief valve in hydraulic pipeline improper; leakage; excessive oil temperature; the door frame carriage are blocked; the pump motor speed is too low. Solution: replace wear or gear pumps; readjust; check and repair; replace faulty hydraulic oil and check the cause of elevated oil temperature; check and adjust; check motor and troubleshoot.

三月，醉一場青春的流年。我們珍惜三月，就像我們珍惜來之不易的幸福青春。三月的雨，三月的風，三月的春光，三月的花香，讓我們沉醉不知?dú)w路，興盡晚回舟。在這樣一場盛大而清新的流年，我們懂得，青春是一種一去不復返的風景，應當好好保護；青春是一種美麗而活躍的熱情，我們必須耐心保持；青春是一種來之不易的懂得，我們必須細心呵護。
 
堆高車油泵壓力不足或速度過慢原因：泵蓋槽內密封圈損壞，內漏過多；齒輪磨損；油泵電機轉速降低；管道中有異物堵塞。解決方法：更換；更換油泵；檢查整流子，清除片間積炭，調整炭刷位置；檢查清洗。
Stack pump pressure or speed is too slow: the pump cover groove sealing ring damage, too much leakage; gear wear; oil pump motor speed down; pipe in the foreign body plug. Solution: replacement; replacement pump; check the commutator, clearance between coke, adjust the brush position check and clean.
三月，醉一場青春的流年。風過無痕，花開向暖。無論是哪一年的三月，都是青春是里最美麗的花朵，都是青春里最難舍的風景，都是青春里最嫵媚的清香。無論在哪一年的三月，無論我們有沒有老去，心中的青春千萬不能割舍，心中的青春永遠跳動著快樂，心中的青春永遠伴隨我們一生一世。
 
堆高車電器運作不不正常：原因：電器盒內微動開關損壞或位置調整不當；主電路保險絲或控制電器保險絲熔斷；電池電壓過低；接觸器觸點燒毛，或污物太多造成接觸不良；觸點不動作。解決方法：更換微動開關，重新調整位置；更換同型號保險絲；重新充電；修理觸點，調整或更換接觸器；檢查接觸器線圈有無斷路或更換接觸器。
Electric stacker operation is not normal: Reason: electric box micro switch is damaged or improperly adjusted position; the main circuit control electric fuse or fuse; the battery voltage is too low; singeing contactor, or too much dirt caused by poor contact; contact action. Solution: replace the microswitch, readjust the position, replace the same type fuse, recharge the battery, repair the contact, adjust or change the contactor, check whether the contactor coil is broken or replace the contactor.