| 立信bfy-2000型高速薄刀分紙機 |
 |
價格：22000 元(人民幣) | 產地：本地 |
| 最少起訂量：1 | 發貨地：本地至全國 | |
| 上架時間：2019-04-03 11:35:01 | 瀏覽量：177 | |
臺州市立信紙箱設備制造有限公司
 |
||
| 經營模式：其他 | 公司類型：生產型,服務型 | |
| 所屬行業：電工產品制造設備 | 主要客戶：全國 | |
 在線咨詢  |
||
| 聯系人:張潮 () | 手機:18969686187 |
電話: |
傳真: |
| 郵箱:188737072@qq.com | 地址:中國浙江省臺州市椒江區 緯二路135號 |
|
包裝材料 紙類 別名 高速薄刀分紙機 產品類型 全新 類型 半自動 適用對象 紙板 售后服務 保修一年 用途 切紙機 適用行業 紙箱包裝 包裝類型 箱 品牌 立信 型號 立信bfy-2200型高速薄刀分紙機 加工定制 是 自動化成度 半自動 詳細說明 目 錄content 一、分切機使用說明書（機械部份）i introduction for use of cutting machine (mechanical part) 二、分切機使用說明書（電器部份）ii introduction for use of cutting machine (electrical part) 三、磨刀器調整說明書iii adjustment explanation of sharpener 四、附圖：電氣原理圖iv. attached drawing: electric schematic diagram 簿刀分切壓痕機使用說明書>; introduction for use of thin-blade cutting creasing machine 分切機使用說明書（機械部分） introduction for use of cutting machine (mechanical part) 一、壓線輪和膠棍的間隙調整 i. adjustment on the clearance between creasing roller and rubber roller 說明：首先松開緊固調節杠螺絲，直接調整手輪，即可調整壓線輪下下壓痕距離。調好后，必須將緊固螺絲緊固，在正常工作中，如發現壓痕過深或過淺，可松開緊固螺絲，隨時調整兩輪距離。 note: firstly, looses the screw fastened the adjustment lever, and then adjusts the hand wheel directly to adjust the lower impress distance under the groove wheel.after adjustment, screw down the fastening screw and during the normal operation, if there is over deep or over shallow impress detected, loose the fastening screw and adjust the distance of two wheels at any time. （膠棍的調整方式完全不一樣，不一一敘述） (the adjustment modes of rubber roller are diversified, here not to illustrate one by one) 二、刀的調整： ii. adjustment of blade 說明：將鎖緊塊松開，用專用工具（配帶的）帶齒的扳手，插入齒條內，左右移動，即可調整刀與刀之間的距離，調好后，必須將緊固螺絲緊固。 note: loosen the locked block and insert it to the rack with special tools (equipped), the wrench with gear, and move horizontally to adjust the distance between blades. after adjustment, it shall screw down the fastening screw. 將刀托恢復原狀，將刀托緊固，將刀刃下縫隙約3-4m/m即可。 recover the state of blade support, and fasten it, leaving about 3-4m/m to the lower seam of blade. 三、薄刀上下的調整： iii. adjustment of the thin blade vertically 說明：只將向上向下的兩個調整螺絲部松開，手握刀盤或擺桿，向上或向下移動即可，調整有效距離，定位后，必須將緊固螺絲緊固，如果不需要四把刀同時使用，只用其中的1-3把刀，可將其他刀抬至**點，然后將螺絲緊固。 note: loose the upper and lower two adjustment screws, move vertically by holding the cutter or rocking beam to adjust the effective distance. after positioning, screw down the fastening screw, if the four blades are not required simultaneously, and only one to three are necessary, lift the other blades to the top and then screw down the screws. 簿刀分切壓痕機使用說明書>; introduction for use of thin-blade cutting creasing machine 分切機使用說明書（電器部分） introduction for use of cutting machine (electrical part) 一、工作準備： i. preparation of work 將啟動掃鈕按下，主電機啟動，調速機開關扳至“on”位置，（紅色）指示燈亮，旋轉調器按鈕，調速表指示在600-800轉/分，（根據切紙情況而定）。定時薄刀開始旋轉，開始送紙板，準備工作，工作前必須手動磨刀，單機有手動磨刀和自動磨刀兩種形式。 press down the starting button and the main engine starts, pull the switch of governor to “on”, the "red” indicator lights, and rotate the button of transponder, and it indicates 600-800 turns/minute (define according to the condition of cutting paper).the timing thin blade rotates and delivers the paperboard. make preparation, and before work, the blade shall be sharpened manually, the single machine has manual sharpening and automatic sharpening two modes. 二、自動/手動磨刀準備： ii. preparation of automatic/manual sharpening 工作前先磨刀：將主機開關扳至“開”位置，電源指示燈亮，將磨刀開關扳至“開”位置，再踩腳踏開關即可磨刀，自動磨刀由時間繼電器控制，用戶可根據實際情況調節磨刀時間。 sharpening before work: pull the switch of main engine to “on” and the power indicator lights, pull the sharpening switch to “on” and step the foot pedal switch to start the sharpening. the automatic sharpening is controlled by the timing relay, and user can adjust the period of sharpening according to the practical situation. 三、工作結束：將調速器旋鈕調回“零”位置，調速器開關置“off”位置，按停止按鈕（紅色指示燈滅）電源關閉，整機停止工作，清理機器。 iii. ending of work: turn the button of regulator to “zero”, and the switch of regulator to “off”, press the stop button (the red indicator extinguishes) to shut down the power, and the whole machine stops, and then cleans the machine. 主機控制電源為380v三相四線制，氣動磨刀控制電源為220v。 the control power of the main engine is of three-phase four-wire system, and the power of pneumatic sharpening control is 220v. 簿刀分切壓痕機使用說明書>; introduction for use of thin-blade cutting creasing machine 磨刀器的調整說明 adjustment explanation of sharpener 整機由兩種調整方式來完成工作 the work of machine is completed with two modes. 一、縱向調整 i. vertical adjustment 它是由壓縮機壓縮空氣驅動汽缸活塞上下運動，運動的距離不超過3—5mm，如果超過此范圍就需要通過定鐵背面的兩個固定螺絲來調整。 it drives the cylinder piston vertically by the compressed air of compressor with the motion distance less than 3 to 5mm. if it is over the scope, adjust with the two fixed screws on the back of fixed iron. 二、橫向調整 ii. horizontal adjustment 它是由砂輪軸承套旁邊的兩個固定螺絲來進行調整，當砂輪和刀由于工作磨損造成間隙過大時，就需要進行橫向調整，動鐵做功時，砂輪作用在刀上，從砂輪邊沿向中心起3—5mm，附圖說明（同圖一）。 it is adjusted by the two fixed screws at the side of grinding wheel bearing holder. when the grinding wheel and blade are of large clearance due to working abrasion, the horizontal adjustment is required. when the moving iron works, the grinding wheel acts on the blade along the side of grinding wheel to the centre of 3 to 5mm, here explains it with the attached drawing (same with fig.1) 機器的保養maintenance of machine 1、軸承套定時加油，每月至少一次，傳動齒輪應按時加油，以免受損。 1. lubrication of bearing holder shall be periodically, for one time every month. the driving gear shall be oiled on time for avoiding damage. 2、三聯體內水霧氣，每班次至少放水一次，油應保持在上限與下限之間，油液不足時，應及時補充油液。 2. water fog of the triplet. out let water for one time at each shift, the oil shall be kept within the lower and upper limit, when the oil level is insufficient, supply the oil timely. 注：應使用2.5—70e，22號汽輪機油。 note: the 2.5—70e, no.22 steam turbine oil shall be used. 簿刀分切壓痕機使用說明書>; introduction for use of thin-blade cutting creasing machine 四、磨刀砂輪的調整：（如圖1） iv. adjustment of the knife grinding wheel (refer to fig.1) 說明：磨刀砂輪可上下左右調整，隨著刀刃的磨損程度而調整砂輪與刀刃之間的有效距離，從而達到磨刀的**效果。 note: the knife grinding wheel can be adjusted vertically and horizontally. according to the abrasion of knife edge, adjust the effective distance of grinding wheel and knife edge, so as to achieve the optimal effect of sharpening. 定鐵fixed iron 動鐵moving iron 砂輪grinding wheel 刀盤cutter 左圖為：定鐵和動鐵做功距離為3-5mm the left figure is drawn upon the distance of 3-5mm between fixed iron and moving iron. 右圖為：動鐵做功時，砂輪作用在刀上3-4mm the right figure is drawn upon 3-4mm that the grinding wheel works on the knife when the moving iron moves. 五、磨刀器氣壓： v. atmospheric pressure of sharpener 說明：手動/自動磨刀必須有恒定的氣壓，三聯體氣壓表的指示為0.6-0.7之間，（廠家已調好，無須再動）方可手動/自動磨刀。 note: the manual/automatic sharpening shall have constant atmosphere pressure. the indicator of triplet gas-pressure meter is between 0.6-0.7 (the manufacturer has adjusted well, please don’t adjust again) to sharpen the knife manually and automatically. 五、 磨刀的說明：vi. introduction of sharpening 將調速表調至600-800轉左右，然后選擇腳踏/自動磨刀。 adjust the regulator meter to be about 600-800 turns and then select pedal/automatic sharpening. 選擇腳踏磨刀，先將氣泵按鈕按下，然后再將磨刀按鈕按下，然后選擇磨刀按鈕，用任何一把刀時，按下相應的按鈕即可腳踏磨刀。 when select the pedal sharpening, press the air pump button at first and then press the sharpening button, when use any knife, press the corresponding button to make pedal sharpening. 四，電氣原理圖 iv electric schematic diagram 電磁閥 solenoid valve 磨刀 sharpening 氣泵 air pump 主機 main engine 急停 emergency stop 機電之家網廠家臺州市立信紙箱設備制造有限公司為您提供立信bfy-2000型高速薄刀分紙機的詳細產品價格、產品圖片等產品介紹信息，您可以直接聯系廠家獲取立信bfy-2000型高速薄刀分紙機的具體資料，聯系時請說明是在機電之家網看到的。 |
| 版權聲明：以上所展示的信息由會員自行提供，內容的真實性、準確性和合法性由發布會員負責。機電之家對此不承擔任何責任。 友情提醒：為規避購買風險，建議您在購買相關產品前務必確認供應商資質及產品質量。 |
機電之家網 - 機電行業權威網絡宣傳媒體
關于我們 | 聯系我們 | 廣告合作 | 付款方式 | 使用幫助 | 會員助手 | 免費鏈接Copyright 2025 jdzj.com All Rights Reserved??技術支持：機電之家 服務熱線：0571-87774297
網站經營許可證:浙B2-20080178
