本公司<\/span>專業生產<\/span>各<\/span>種類型規格<\/span>托輥<\/span>、滾筒、托輥支架<\/span>、<\/span>直徑范圍為89mm-1<\/span><\/span>59<\/span>mm,適用機械<\/span><\/span>**<\/span>、<\/span>火電、建材、<\/span>礦山等行業,<\/span>量大從優,<\/span>歡迎新老<\/span>客戶<\/span>前來訂購<\/span>。<\/span><\/span> <\/p> !<\/span><\/span> <\/p> <\/span> <\/p> <\/span> <\/span>關于托輥<\/span><\/span> <\/p> 一<\/span> <\/span>概述<\/span><\/span> <\/p> 托輥<\/span>是安裝在輸送機上用來支撐輸送帶和輸送帶上所裝載的物料,它減少了物料對輸送帶的沖擊。托輥的技術參數隨輸送帶的寬度和輸送量的不同而不同。<\/span><\/span> <\/p> 二<\/span> <\/span>產品型號含義<\/span><\/span> <\/p> Ø108×375×408×205 <\/span><\/span> <\/p> <\/span>管體直徑<\/span>×<\/span>管體長度<\/span>×<\/span>軸長度<\/span>×<\/span>軸承型號<\/span><\/span> <\/p> 三<\/span> <\/span>托輥執行標準<\/span><\/span> <\/p> GB/T 10595-2009 <\/span>帶式輸送機標準<\/span><\/span> <\/p> 四<\/span> <\/span>托輥結構<\/span><\/span> <\/p> 五<\/span> <\/span>托輥綜合機械性能<\/span><\/span> <\/p> <\/span> <\/p> <\/span> <\/p> <\/span> <\/p> <\/span> <\/p> <\/span> <\/p> <\/span> <\/p> <\/span> <\/p> <\/span> <\/p> (<\/span>1<\/span>)轉動靈活,旋轉阻力小。托輥組模擬摩擦系數<\/span>C≤0.7mm.<\/span><\/span> <\/p> (<\/span>2<\/span>)托輥徑向跳動量為:<\/span>L=200-530mm<\/span>為<\/span><0.5mm<\/span>,<\/span>L=600-800<\/span>為<\/span><0.7mm<\/span>,<\/span>L=900-2000mm<\/span>為<\/span><1.3mm<\/span>。<\/span><\/span> <\/p> <\/span>(<\/span>3<\/span>)托輥軸向位移量<\/span>≤0.7mm<\/span>(在<\/span>500N<\/span>軸向壓力作用下)。<\/span><\/span> <\/p> <\/span>(<\/span>4<\/span>)托輥設計壽命為<\/span>30000<\/span>小時,其損壞率不超過<\/span>10%<\/span>(不包括緩沖托輥等特殊托輥)。<\/span><\/span> <\/p> <\/span>(<\/span>5<\/span>)防塵,防水性能好,按<\/span>GB/T 10595-2009<\/span>的要求,托輥以<\/span>550r/min<\/span>旋轉時,其防塵與防水性能應滿足以下要求:<\/span><\/span> <\/p> 在具有煤塵的容器內,連續運轉<\/span>200<\/span>小時后,煤塵不得進入軸承潤滑脂內,在淋水工況條件下,連續運轉<\/span>72<\/span>小時后,進水量不的超過<\/span>150<\/span>克。<\/span><\/span> <\/p> (6) Ø89-Ø108<\/span>施加的軸向載荷<\/span>10000N,Ø133-Ø159<\/span>施加的軸向載荷<\/span>15000N<\/span>時<\/span>,<\/span>托輥軸<\/span>(<\/span>包括軸承座<\/span>,<\/span>密封件<\/span>)<\/span>與托輥管體無脫開現象。<\/span><\/span> <\/p> <\/span> <\/p> <\/span> <\/p> <\/span> <\/p> <\/span> <\/p> <\/span> <\/p> 六<\/span> <\/span>安裝<\/span> <\/span>調整<\/span><\/span> <\/p> 將托輥掛于皮帶機上已安裝好的托輥架上<\/span>,<\/span>上好相應的聯接件<\/span>.<\/span>托輥上表面應位于同一平面上<\/span>(<\/span>水平面或傾斜面<\/span>)<\/span>或者在一個公共半徑的弧面上<\/span>(<\/span>輸送機凹弧段或凸弧段<\/span>),<\/span>在相鄰三組托輥之間其高低<\/span>,<\/span>固定式輸送機不大于<\/span>2mm,<\/span>伸縮和吊掛式輸送機不大于<\/span>3mm<\/span>。<\/span><\/span> <\/p> 七<\/span> <\/span>使用<\/span> <\/span>操作<\/span><\/span> <\/p> (1) <\/span>必須保持托輥良好<\/span>,<\/span>有清潔的工作環境<\/span>.<\/span>驅動裝置關閉后<\/span>,<\/span>對托輥進行經常性的檢查<\/span>,<\/span>調整<\/span>,<\/span>維護和清掃。<\/span><\/span> <\/p> (2) <\/span>輸送帶運輸時<\/span>,<\/span>邊緣不得超出托輥筒體邊緣。<\/span><\/span> <\/p> 八<\/span> <\/span>使用環境條件<\/span><\/span> <\/p> (1) <\/span>環境溫度<\/span> |